Cleaning knowledge

Putting a cleaning robot into service: routes, refill points and operator handover

Mark access controls, narrow passages, glass partitions, pedestrian crossings and temporary obstructions on a floor plan before selecting an autonomous route. Compare the dimensions and delivered functions of the J-W70, CC1 or AllyBot-C2 separately. Check lifts, access gates and any docking station against the specific installation.

Read the article Discuss equipment selection

Putting a cleaning robot into service: routes, refill points and operator handover

Cleaning knowledge2026-11-01Wan Sheng Long Cleaning Equipment

Assign a person and a place for filling, draining, charging and consumable checks. Where a station is proposed, check water, drainage, power and network access before planning the shift.

Run one representative route under supervision. Inspect pickup and recovery at the narrowest turn, observe how the operator deals with a temporary obstacle and check what happens at the end of the task. Record who takes over, how the area is secured and where the machine stopped. Refer drive and electrical faults to qualified service staff.

Checks after reading

Site area, routes and narrowest access
Floor, dust, oil, debris or pipe-blockage type
Daily frequency and continuous working time
Power, water, wastewater, consumables and service conditions

Explore products and selection information

Cleaning equipment catalogueView categories, models, specifications and applications Industry application solutionsExplore equipment combinations for property, factory, municipal and commercial sites

FAQ

Putting a cleaning robot into service: routes, refill points and operator handover — frequently asked questions

What does this article address?

What site information is needed before equipment selection?

Provide area, aisle width, floor/pipe conditions, contamination, frequency, power/water, city and budget range.

Should we trial route management and manual takeover before deploying an autonomous cleaner?

This article offers selection guidance. For complex sites, heavy contamination or continuous work, verify models and configurations through equipment information, video or a trial.

Apply the selection method to each machine

J-W70 | Planning longer autonomous scrubbing routes with a large tank and replenishment options

For continuous hard-floor routes in commercial buildings, match tank capacity and replenishment to the fixed cleaning route. Assign inspections and manual takeover.

Plan cleaning and service points together. Measure coverage on site. Confirm the workstation and automatic supply equipment included with the specific version.

Approximately 3 hours of scrubbing and 10 hours of dry mopping are figures for separate modes. Apply each only to its stated duty.

Assess this machine for your site →

AllyBot-C2 combines a compact body with washing, pickup and dust mopping for zoned indoor cleaning.

For everyday indoor commercial aisles, plan scrubbing, vacuuming and dry mopping by zone. Allow for the compact machine, replenishment and operator intervention.

Check the 503 × 503 mm plan dimensions and measure clearance on the route. Observe how the 10 L hopper fills with the actual material before estimating area per run.

Automatic charging is documented. Confirm water filling, draining, lift integration, door access and multi-floor operation separately.

Assess this machine for your site →

CC1 can sweep, scrub, vacuum and mop. Match the operating mode to each area.

For mixed wet and dry tasks in commercial public areas, specify sweeping, scrubbing, vacuuming and dry mopping by mode. Test each separately and assign supervision.

Set separate acceptance points for sweeping and scrubbing. Automatic water filling and draining require a compatible station. Charging alone covers only the battery.

The specification lists cleaning reports and resumption after interruption. Check actual coverage, exceptions and manual finishing.

Assess this machine for your site →

MT1: AI patrol, standard sweeping, litter recognition and dry collection

For dry litter in factories, warehouses and large commercial areas, plan AI patrol and standard sweeping separately. Assign unloading, inspection and intervention to staff.

Exclude hazardous or special material first. Separate people and traffic even for ordinary litter. Assign emptying and inspection duties separately from automatic charging.

Coordinate task management, automatic charging and resumption with inspection, waste removal and manual takeover.

Assess this machine for your site →

J-S130 | 1,300 mm sweeping width and 130 L hopper for controlled site roads

For repeat patrols on regular roads within enclosed sites, match sweeping width and hopper capacity to the route. Check traffic boundaries and manual disposal before deployment.

Define where patrols are permitted. Confirm any public-road approval independently. Plan emptying of the 130 L hopper around the load and check automatic emptying, charging and station integration individually.

The documented sensors are LiDAR, an IMU and cameras. Verify charging, discharge, lift and door integration separately.

Assess this machine for your site →