01 Intended use
- Wide ride-on cleaning, first divide the route
- Separate continuous areas from dense obstacle zones for arrangement, avoiding selection based solely on total area.
Jinjie Floor Scrubber
Jinjie J-960B Wide Ride-On Floor Scrubber
The Jinjie J-960B is a wide ride-on scrubber for open public hard-floor aisles, with 960 mm coverage and 180 L/200 L tanks. Assess pillars, pedestrian flows, working windows and recovery together.
Established in 2004 | Site-trial discussion | Service support across China
Theoretical calculation speed:10 km/hTheoretical cleaning coverage (calculated)9600㎡/hWebsite theoretical comparison calculation; not actual productivity.
02 Key performance figures
- Cleaner width and water tank configuration.
- 960 mm clear width; water tank capacity 180 L / 200 L. Actual performance should be confirmed in combination with the floor material, dirt type, and on-site trial operation.
03 Working configuration
- Operation and daily usage scheduling
- Operated by personnel. When selecting, confirm battery, charging location, and daily inspection and maintenance arrangements together.
Start with your site
Choose the area that best matches your site
First, check whether the main hall, long corridors, and connecting doorways form a continuous route, and then determine the coverage value of the wide-path equipment. J-960B should be measured based on the entire machine, the squeegee, and the rotation conditions through the space. Data not listed in the materials should not be estimated based on battery capacity; actual shifts should be based on trial washing, replenishment of water discharge, and charging arrangements.
What is the clear width of your floor scrubber?
First, check the on-site conditions, then determine the appropriate equipment configuration together.
Commercial spaces and shopping malls.
Channel width, turning position, business hours.
Office and public buildings
Handling large crowds, corridors, and elevators
Property management garage and public areas
Conditions of hard surfaces, drainage, and ramps
Factory and warehouse floor cleaning equipment.
Oil stains, dust, obstacles, and work routes
| Site type | The on-site conditions for joint checking | J-960B Selection Recommendation |
|---|---|---|
| Commercial spaces and shopping malls. | Channel width, turning position, business hours. | First confirm whether the equipment can turn and pass, then divide the continuous cleaning area. |
| Office and public buildings | Handling large crowds, corridors, and elevators | Verify the passage and floor transfer conditions; in narrow areas, pair with smaller models. |
| Property management garage and public areas | Conditions of hard surfaces, drainage, and ramps | Clarify and level the work area; slopes and elevation differences must be checked against the technical specifications of this machine. |
| Factory and warehouse floor cleaning equipment. | Oil stains, dust, obstacles, and work routes | First distinguish the type of dirt and the floor surface material, then arrange pre-treatment, brushing, and wastewater recovery. |
Daily cleaning, try a more convenient method.
How can we reduce the effort of pushing the machine over a large floor?
Starting from the areas you clean daily, consider how driving operations, brushing, and wastewater recovery can be integrated into your daily routine. Please let us know your route and usage schedule, and we will assess together.
01
How to schedule cleaning in coordination with production?
Schedule cleaning zone by zone around production. Check the soil, clearances between machines and travel routes before planning scrubbing and wastewater recovery.
Look at relevant scenarios →
02
How to arrange routes when there are a lot of goods and vehicles
Perform operations in sections according to the rack and passage division, and confirm the turning space, vehicle passage, and drainage and replenishment positions together, making the cleaning more systematic.
Look at relevant scenarios →
03
The route is long, and manual pushing is labor-intensive.
Operator-driven operation reduces the need for prolonged pushing along long routes, with the machine cleaning and recovering wastewater in designated parking areas and main channels, and the slope conditions are also checked together.
Look at relevant scenarios →TECHNICAL SPECIFICATIONS
Ride-On Floor ScrubbersJ-960B configuration and technical parameters
First understand several configurations closely related to daily use. Detailed specifications are also organized below for easy comparison.
First check these core configurations.
Cleaning width960mm
Fresh water tank / Sewage water tank180L / 200L
Battery36V × 200Ah
Theoretical cleaning coverage (calculated)9600㎡/h
Machine dimensions1580 × 1100 × 1260mm
Operating voltage36V
Full specifications for ViewCleaning performance · Power and charging · Overall configurationExpand or collapse
Detailed equipment specifications
| Key operating figures | |||
|---|---|---|---|
| Cleaning width | 960mm | Squeegee width | 1100mm |
| Clean water tank | 180L | sewage tank | 200L |
| Theoretical cleaning coverage (calculated) | 9600㎡/h | Maximum climbing capability | 15° |
| Theoretical calculation speed | 10 km/h | Brush roll speed | 180rpm |
| Brush roll pressure | 70kPa | ||
| Drive and electrical system | |||
| Operating voltage | 36V | Battery | 36V × 200Ah |
| Travel motor | 800W | Brush motor | 2 × 450W |
| Recovery motor | 730W | ||
| Machine configuration | |||
| Machine dimensions | 1580 × 1100 × 1260mm | Product model | J-960B |
| Work method | Ride-on floor cleaning | Minimum turning radius | 1130mm |
How do these figures apply to your site?
Note: website theoretical coverage for ride-on scrubber-dryers is calculated as cleaning width × the standard theoretical calculation speed of 10 km/h. It is for theoretical area comparisons, not actual productivity or the machine's maximum travel speed.
Look beyond the numbers: consider how they affect large-zone coverage, filling/draining frequency, continuous routes and access.
9600 m²/h is calculated from the confirmed cleaning width × the website theoretical calculation speed of 10 km/h. It is for theoretical coverage comparisons only, not actual or measured productivity.
Drive-type operation.Brushing and cleaning.Extract wastewater
Look at the picture to understand the equipment.
Components and their functions
01 Driving and Drive
Sitting driving to reduce the continuous pushing over longer routes, and operating in coordination with on-site traffic.
02 brushing configuration
960 mm clear width, brush disk motor 2 × 450 W; determine the cleaning configuration based on the floor material and dirt.
03 Wastewater recovery
The width of the squeegee is 1100 mm. The washing and wastewater recovery system combines, and actual residual water can be confirmed through on-site testing.
04 Dual water tank configuration
180 L clear water tank, 200 L wastewater tank, combine zone division and water and drainage position arrangement for operations
05 Battery and Shifts
36 V working voltage, battery is 36 V × 200 Ah; schedule shifts according to actual working conditions and charge accordingly.
06 Route and traffic
Check together the entrance, passage, turning space, ramp, and slippery areas for additional confirmation.
Understanding the specifications
How do these configurations correspond to your daily work?
Digital solutions must ultimately be put to use: how the route is arranged, whether water and drainage are convenient, and how shifts are scheduled. We combine key configurations with on-site conditions to help you make judgments.
960 mm clear width, combined with actual route arrangement for continuous operation.
Check together: narrowest entrance / passage / turning space.180 L clear water tank and 200 L wastewater tank, coordinate with zone division cleaning arrangement
Take a look: water refill points / drainage points / cleaning area per session.Combine the machine's drive configuration and on-site route to reduce continuous pushing.
Take a look: continuous route / operating habits / ramp conditions.Arrange shifts based on the machine's battery and actual usage conditions.
Take a look: daily operating time / usage frequency / charging location.Judge together whether it is appropriate
Is J-960B suitable for you? Let's compare together
In these cases, you can first refer to J-960B.
- Large continuous hard-floor areas
- Underground car parks, logistics parks, airports, stations and large shared areas
- Open routes with ride-on access
- Need fewer filling/draining stops and repeated manual trips
These requirements also warrant comparison with other models.
- Not recommended for confined spaces or frequent tight turns
- For smaller areas, compare J-D9BF/J-85BH or a smaller model
- Pre-clear substantial loose debris first
- If there are steps or slippery areas, confirm the passage conditions together.
Compare related models
How to choose the right model for J-960B compared to similar models?
Place the three models together and see the differences in configuration and operating method.
| Comparison criteria |  J-920B → | J-960B → |  J-105BF → |
|---|---|---|---|
| Cleaning width | 920mm | 960mm | 1050mm |
| Squeegee width | 1260mm | 1100mm | 1300mm |
| Clean water tank | 160L | 180L | 180L |
| sewage tank | 165L | 200L | 190L |
| Battery configuration | 6 × 6V × 200Ah | 36V × 200Ah | 6 × 6V × 200Ah |
| Work time for the data. | 6h | Request the specification for this configuration. | 4–6h |
| Operating method | Operator-controlled. | Operator-controlled. | Operator-controlled. |
First, check the passage and operation methods, then compare the water tank, working time, and maintenance schedule. The data in the table is based on the current technical specifications of each model. The working time in the documentation does not equal the actual runtime under all operating conditions.
Related articles
Are there any questions about selection? You can continue to look at these contents.
Operating cost
How can the usage cost of J-960B be calculated more accurately in the field?
Compare using the same floor, same cleaning requirements, and actual records.
First, record the actual investment.
Labor cost = number of people × actual working hours × hourly labor cost.
Record actual expenditure on tools, detergent and clean-up.
Include operation and maintenance together
Single-use cost = operator labor + water and electricity with cleaning agent + consumable maintenance allocation + equipment investment allocation.
Turns, water replenishment, sewage discharge, and cleaning conclusion should all be counted as actual working time.
From the site, let's select the appropriate one together.
Understand similar operating conditions, then confirm the suitability of this machine.
First, check the application scenario of this page. Combine it with your floor type, route, and work schedule to make a judgment. Real customer projects are only displayed according to the verified model, and the scenario images are not used as proof of customer results.
Understand customer applications → Talk about the site and trial run →Service support
Operating and maintaining the machine after delivery
Delivery inspection
Check the equipment and configuration list together before delivery.
Understand service arrangements →Operator training
Communicate startup, brushing, replenishment of water, and daily cleaning.
Understand service arrangements →Usage guidance
In case of operational issues, communicate with the model and usage conditions.
Understand service arrangements →Parts supply
Check the brush roll, rubber strip, and other parts against the model.
Understand service arrangements →On-site fault repair
Service scope, costs, and arrival arrangements need to be confirmed first.
Understand service arrangements →Scheduled on-site maintenance
Coordinate maintenance plans with the frequency of use and the location.
Understand service arrangements →— FAQ
Choosing and using the J-960B: frequently asked questions
Which large public-area tasks suit the J-960B scrubber?
Consider open hard floors that can form continuous routes. Pedestrians, pillars and temporary fixtures may interrupt them. Assess safe working windows and accessible coverage; a large area alone does not establish that wider equipment is suitable.
How should doors, aisles and turns be checked for the wide J-960B scrubber?
Measure the door and passage according to the machine body, squeegee, and personnel safety space. Then test the turning and parking. 960 mm brushing coverage cannot replace the overall machine passage dimensions. Storage, charging, and maintenance locations should also be included in the route check.
How should water stops be planned for J-960B's 180 L and 200 L tanks?
It can be used as input for calculating the replenishment and drainage schedule, but the frequency still depends on the water supply and the amount of waste. If the drainage point is far away, the large water tank cannot eliminate the round trip, so the replenishment route and manual management should be included in the shift.
How should working time be assessed for J-960B's 36 V/200 Ah battery configuration?
Check the delivered battery, matching charger and instructions, then record energy use and supply stops under the actual load and operating method. A 36 V/200 Ah rating alone does not establish fixed runtime. Do not invent an unconfirmed duration; schedule from site records.
How should actual ride-on cleaning productivity be assessed in public areas?
It is 0.96 m × a uniform theoretical 10 km/h, not a cleaning or safe-driving speed recommendation. Turning, yielding, water handling and finishing affect output, which needs representative route records.
How should wide J-960B and J-920B ride-on scrubbers be compared?
Keep the task constant and compare 960 mm and 920 mm coverage, envelopes and turns, then tanks, power and replenishment. Do not turn the width difference directly into an efficiency or staffing percentage.
How should water residue, turns and finishing be assessed in a public-area trial?
Trial representative surfaces and soil with suitable equipment and inspect removal, surface changes and residual water after straight passes and turns. Agree observation methods first; photographs or theoretical efficiency are not measured proof.
What information does Wanshenglong need for a J-960B configuration proposal?
The client requires information on the layout of the hall and corridors, peak hours for pedestrian traffic, the type of floor material and its dirt level, the conditions at doorways and corners, and the replenishment and drainage conditions. Around the Jinjie equipment, the trial use, handover, operation training, and maintenance of accessories will be discussed. The specific service scope will be confirmed according to the project.
Discuss the floor, routes, and daily cleaning schedule, and together see if J-960B is suitable.
Phone consultation: 0755-25621811 View other contact information →
Product enquiryDiscuss your site, and together see if J-960B is suitable
Tell us about the usage area and the issues you hope to improve, and the equipment consultant will combine with the passage, ground and work arrangement, communicate the suitable configuration with you. The area is temporarily unclear, you can contact us first.