01 Intended use
- Planning a complete operation route for large ride-on floor scrubbers
- Arrange the cleaning area, water supply point, drainage point, and charging position together.
Jinjie Floor Scrubber
Jinjie J-920B Large Ride-On Floor Scrubber
The Jinjie J-920B is a large ride-on scrubber for relatively open property main aisles, with 920 mm coverage and 160 L/165 L tanks. Plan the main route, replenishment and finishing responsibilities together.
Established in 2004 | Site-trial discussion | Service support across China
Theoretical calculation speed:10 km/hTheoretical cleaning coverage (calculated)9200㎡/hWebsite theoretical comparison calculation; not actual productivity.
02 Key performance figures
- Cleaner width and water tank configuration.
- 920 mm clear width; water tank capacity 160 L / 165 L. Actual performance should be confirmed in combination with the floor material, dirt type, and on-site trial operation.
03 Working configuration
- Operation and daily usage scheduling
- Operated by personnel. When selecting, confirm battery, charging location, and daily inspection and maintenance arrangements together.
Start with your site
Choose the area that best matches your site
Draw the main path, column sides, doorways, and the manual finishing area on the same route, and then check the surrounding space related to the 1260 mm squeegee. The capacity and coverage of J-920B should be determined together with the replenishment and drainage location, shift times, and transportation conditions. A large water tank cannot replace on-site trial washing, and theoretical efficiency cannot be directly used to calculate manual replacement.
How can large ride-on floor scrubbers be coordinated with your site?
First, check the on-site conditions, then determine the appropriate equipment configuration together.
Commercial spaces and shopping malls.
Channel width, turning position, business hours.
Office and public buildings
Handling large crowds, corridors, and elevators
Property management garage and public areas
Conditions of hard surfaces, drainage, and ramps
Factory and warehouse floor cleaning equipment.
Oil stains, dust, obstacles, and work routes
| Site type | The on-site conditions for joint checking | J-920B Selection Recommendation |
|---|---|---|
| Commercial spaces and shopping malls. | Channel width, turning position, business hours. | First confirm whether the equipment can turn and pass, then divide the continuous cleaning area. |
| Office and public buildings | Handling large crowds, corridors, and elevators | Verify the passage and floor transfer conditions; in narrow areas, pair with smaller models. |
| Property management garage and public areas | Conditions of hard surfaces, drainage, and ramps | Clarify and level the work area; slopes and elevation differences must be checked against the technical specifications of this machine. |
| Factory and warehouse floor cleaning equipment. | Oil stains, dust, obstacles, and work routes | First distinguish the type of dirt and the floor surface material, then arrange pre-treatment, brushing, and wastewater recovery. |
Daily cleaning, try a more convenient method.
How can we reduce the effort of pushing the machine over a large floor?
Starting from the areas you clean daily, consider how driving operations, brushing, and wastewater recovery can be integrated into your daily routine. Please let us know your route and usage schedule, and we will assess together.
01
The route is long, and manual pushing is labor-intensive.
Operator-driven operation reduces the need for prolonged pushing along long routes, with the machine cleaning and recovering wastewater in designated parking areas and main channels, and the slope conditions are also checked together.
Look at relevant scenarios →
02
How to arrange routes when there are a lot of goods and vehicles
Perform operations in sections according to the rack and passage division, and confirm the turning space, vehicle passage, and drainage and replenishment positions together, making the cleaning more systematic.
Look at relevant scenarios →
03
How can we clean a large area while people are moving through it?
Coordinate cleaning schedules with foot traffic, combining brushing and wastewater recovery to reduce repeated scrubbing and accommodate personnel movement.
Look at relevant scenarios →TECHNICAL SPECIFICATIONS
Ride-On Floor ScrubbersJ-920B configuration and technical parameters
First understand several configurations closely related to daily use. Detailed specifications are also organized below for easy comparison.
First check these core configurations.
Cleaning width920mm
Fresh water tank / Sewage water tank160L / 165L
Runtime reference6h
Battery6 × 6V × 200Ah
Theoretical cleaning coverage (calculated)9200㎡/h
Machine dimensions1450 × 930 × 1100mm
Full specifications for ViewCleaning performance · Power and charging · Overall configurationExpand or collapse
Detailed equipment specifications
| Key operating figures | |||
|---|---|---|---|
| Cleaning width | 920mm | Squeegee width | 1260mm |
| Clean water tank | 160L | sewage tank | 165L |
| Runtime reference | 6h | Theoretical cleaning coverage (calculated) | 9200㎡/h |
| Theoretical calculation speed | 10 km/h | Brush roll speed | 220rpm |
| Brush arrangement | Metal reduction gears for the brush drive | ||
| Drive and electrical system | |||
| Operating voltage | 36V | Battery | 6 × 6V × 200Ah |
| Brush motor | AM 2 × 550W | ||
| Machine configuration | |||
| Machine dimensions | 1450 × 930 × 1100mm | Machine weight | 632kg |
| Product model | J-920B | Work method | Ride-on |
How do these figures apply to your site?
Note: website theoretical coverage for ride-on scrubber-dryers is calculated as cleaning width × the standard theoretical calculation speed of 10 km/h. It is for theoretical area comparisons, not actual productivity or the machine's maximum travel speed.
Look beyond the numbers: consider how they affect filling/draining frequency, cleaning coverage, continuous routes and site access.
9200 m²/h is calculated from the confirmed cleaning width × the website theoretical calculation speed of 10 km/h. It is for theoretical coverage comparisons only, not actual or measured productivity.
Drive-type operation.Brushing and cleaning.Extract wastewater
Look at the picture to understand the equipment.
Components and their functions
01 Driving and Drive
Sitting driving to reduce the continuous pushing over longer routes, and operating in coordination with on-site traffic.
02 brushing configuration
The cleaning width is 920 mm. The brush motor specification is AM 2 × 550 W. Select the brush to suit the floor and the type of soil.
03 Wastewater recovery
The width of the squeegee is 1260 mm. The washing and wastewater recovery system combines, and actual residual water can be confirmed through on-site testing.
04 Dual water tank configuration
160 L clear water tank, 165 L wastewater tank, combine zone division and water and drainage position arrangement for operations
05 Battery and Shifts
36 V working voltage, battery is 6 × 6 V × 200 Ah; schedule shifts according to actual working conditions.
06 Route and traffic
Check together the entrance, passage, turning space, ramp, and slippery areas for additional confirmation.
Understanding the specifications
How do these configurations correspond to your daily work?
Digital solutions must ultimately be put to use: how the route is arranged, whether water and drainage are convenient, and how shifts are scheduled. We combine key configurations with on-site conditions to help you make judgments.
920 mm clear width, combined with actual route arrangement for continuous operation.
Check together: narrowest entrance / passage / turning space.160 L clear water tank and 165 L wastewater tank, coordinate with zone division cleaning arrangement
Take a look: water refill points / drainage points / cleaning area per session.Combine the machine's drive configuration and on-site route to reduce continuous pushing.
Take a look: continuous route / operating habits / ramp conditions.Arrange shifts based on the machine's battery and actual usage conditions.
Take a look: daily operating time / usage frequency / charging location.Judge together whether it is appropriate
Is J-920B suitable for you? Let's compare together
In these cases, you can first refer to J-920B.
- Large continuous hard-floor areas
- Underground car parks, logistics parks, airports, stations and large shared areas
- Open routes with ride-on access
- Need fewer filling/draining stops and repeated manual trips
These requirements also warrant comparison with other models.
- Not recommended for confined spaces or frequent tight turns
- For smaller areas, compare J-D9BF/J-85BH or a smaller model
- Pre-clear substantial loose debris first
- If there are steps or slippery areas, confirm the passage conditions together.
Compare related models
How to choose the right model for J-920B compared to similar models?
Place the three models together and see the differences in configuration and operating method.
| Comparison criteria |  J-85BH → | J-920B → |  J-960B → |
|---|---|---|---|
| Cleaning width | 850mm | 920mm | 960mm |
| Squeegee width | 1100mm | 1260mm | 1100mm |
| Clean water tank | 110L | 160L | 180L |
| sewage tank | 115L | 165L | 200L |
| Battery configuration | 4 × 6V × 200Ah | 6 × 6V × 200Ah | 36V × 200Ah |
| Work time for the data. | 4.5–6h | 6h | Request the specification for this configuration. |
| Operating method | Operator-controlled. | Operator-controlled. | Operator-controlled. |
First, check the passage and operation methods, then compare the water tank, working time, and maintenance schedule. The data in the table is based on the current technical specifications of each model. The working time in the documentation does not equal the actual runtime under all operating conditions.
Related articles
Are there any questions about selection? You can continue to look at these contents.
Combine the machine's configuration to continue understanding these issues.
- How to stock parts and consumables: brush roll, rubber strip, motor, charger, and cleaner.Consumable ledger and inventory management for multi-project cleaning equipment
Operating cost
How can the usage cost of J-920B be calculated more accurately in the field?
Compare using the same floor, same cleaning requirements, and actual records.
First, record the actual investment.
Labor cost = number of people × actual working hours × hourly labor cost.
Record actual expenditure on tools, detergent and clean-up.
Include operation and maintenance together
Single-use cost = operator labor + water and electricity with cleaning agent + consumable maintenance allocation + equipment investment allocation.
Turns, water replenishment, sewage discharge, and cleaning conclusion should all be counted as actual working time.
From the site, let's select the appropriate one together.
Understand similar operating conditions, then confirm the suitability of this machine.
First, check the application scenario of this page. Combine it with your floor type, route, and work schedule to make a judgment. Real customer projects are only displayed according to the verified model, and the scenario images are not used as proof of customer results.
Understand customer applications → Talk about the site and trial run →On-site applications
J-920B Application Real Shots
Zhongshan Taomei warehouse application
Zhongshan Taomei warehouse application
The J-920B cleans a warehouse floor with the work planned around stored goods and operating aisles.
- Warehouse-aisle floor cleaning
- Cleaning organised around storage activities
J-920B delivery to Wanli Tire
View the original delivery photograph and the related ride-on scrubber.
View delivery case →Service support
Operating and maintaining the machine after delivery
Delivery inspection
Check the equipment and configuration list together before delivery.
Understand service arrangements →Operator training
Communicate startup, brushing, replenishment of water, and daily cleaning.
Understand service arrangements →Usage guidance
In case of operational issues, communicate with the model and usage conditions.
Understand service arrangements →Parts supply
Check the brush roll, rubber strip, and other parts against the model.
Understand service arrangements →On-site fault repair
Service scope, costs, and arrival arrangements need to be confirmed first.
Understand service arrangements →Scheduled on-site maintenance
Coordinate maintenance plans with the frequency of use and the location.
Understand service arrangements →— FAQ
Choosing and using the J-920B: frequently asked questions
Which large property and garage tasks suit the J-920B scrubber?
Consider open hard-floor main aisles and long continuous routes. Pillars, vehicles and furniture can interrupt coverage. Separate machine-accessible areas from manual finishing instead of selecting only by total building area.
How should access be checked for J-920B's 920 mm width and 1260 mm squeegee?
The former is used to determine the brushing coverage, while the latter relates to the wastewater recovery and the outer space. The entrance, turns, and storage location should be verified against the entire machine and the squeegee in actual condition; the 920 mm cannot be considered as the passage width.
How should J-920B's 160 L and 165 L tanks be managed on long routes?
First, confirm the water intake, drainage, and parking positions in each area, and record the supply route with water volume, waste material, and refilling frequency. The 160 L clean water tank and 165 L dirty water tank help in planning water supply and drainage, but battery duration and cross-area trips still need to be separately listed in the shift schedule.
How should J-920B charging and extended cleaning shifts be planned?
The time is based on the current configuration and is subject to the battery status and brush washing, as well as driving load. Scheduling also needs to include charging, refilling and draining, and wrapping up, and cannot be promised as a fixed continuous brushing of 6 hours for each project.
How should actual productivity be checked in a large ride-on scrubber trial?
Agree floor, soil, route and result criteria, then time turns, yielding, water handling and finishing as part of the trial. The theoretical 9200 m²/h supports configuration comparison; plan shifts from completed area and total time.
How should J-920B and J-960B large ride-on scrubbers be compared?
First, compare the effective coverage, turning, and retrieval capabilities of the same main channel. Then verify each unit's water tank, overall dimensions, battery, and transfer conditions. A wider machine is not necessarily suitable for doorways or routes with many obstacles; do not rely solely on numerical comparisons.
How should J-920B brushes, blades and tanks be checked after work?
Turn off the machine according to the instructions, clean the wastewater tank, and check the condition of the recovery path, rubber seals, and brushes. Charge and store it according to the delivery requirements. The maintenance passage and drainage location should also be reserved, not just considering the passage space during operation.
What property information helps Wanshenglong specify J-920B?
Provide property main routes, doors, turns, surface, soil, water points and shifts, and identify who finishes edges. Wanshenglong can discuss trials and training for the actual Jinjie version subject to project arrangements.
Discuss the floor, routes, and daily cleaning schedule, and together see if J-920B is suitable.
Phone consultation: 0755-25621811 View other contact information →
Product enquiryDiscuss your site, and together see if J-920B is suitable
Tell us about the usage area and the issues you hope to improve, and the equipment consultant will combine with the passage, ground and work arrangement, communicate the suitable configuration with you. The area is temporarily unclear, you can contact us first.