01 Intended use
- Factory perimeter and public roads
- Allow for kerbside pickup, road coverage, access and the available working window.
Jinjie road sweepers
Jinjie J-XS1450 ride-on sweeper
The Jinjie J-XS1450 ride-on sweeper combines 1450 mm coverage and a 160 L hopper for factory aisles, parking and property roads, supporting route-based selection and organised disposal.
1450 mm sweeping width and a 160 L hopper combine route coverage with collection capacity.
Theoretical calculation speed:12 km/hTheoretical sweeping coverage (calculated):17400㎡/hWebsite theoretical comparison calculation; not actual productivity.
02 Key performance figures
- 1450 mm sweeping width
- Observe collection, residual debris and dust on a representative section of your route.
03 Working configuration
- Ride-on controls and 160 L hopper
- Plan disposal around debris volume, weight and distance. Maintain the machine as instructed.
Product and operation video
J-XS1450 equipment and operation
View the model's appearance and operation; discuss configuration against actual site conditions.
Ask about selecting J-XS1450
Provide cleaning tasks, site conditions and frequency to confirm suitable configuration.
Enquire about this modelStart with your site
What would you like to clean?
Typical applications
Which routine sweeping tasks suit J-XS1450?
Property / estate main roads
View detailed analysis →Continuous estate main-road sweeping
For leaves, paper and ordinary light debris on estate main roads and property perimeters.
Factory / warehouse surroundings
View detailed analysis →Longer factory and warehouse routes
For dust, fragments and light debris along factory roads, warehouse surroundings and longer industrial-estate routes.
Campus / visitor attraction / commercial surroundings
View detailed analysis →Longer public-area routes
For regular fixed-route sweeping around campuses, visitor attractions and commercial sites.
Cleaning challenges
Common challenges on longer sweeping routes
Repeated manual sweeping of long estate, factory and warehouse-perimeter routes occupies staff and time.
Higher volumes of leaves and paper can cause frequent interruptions with a smaller hopper.
Pass coverage must suit estate roads, corners and available access.
Site conditions, configuration and selection
How would J-XS1450 work on your site?
Assess open areas separately from columns, bays and gateways. Compare coverage and collection on continuous routes and turns and traffic in complex areas. Include filter care and disposal in trials and check power and brushes.
Residential and industrial estate roads
Clear road width, kerbs, leaf load and pedestrian hours
Factory and warehouse yards
Waste type, traffic, surface and distance to disposal
Car parks and connecting lanes
Gate height, narrowest section, columns and gradients
Campus and public roads
Pedestrian traffic, obstructions, level changes and disposal arrangements
Check access, debris and work patterns at the site when specifying the machine.
| Site type | Configuration and operating conditions to check | Selecting J-XS1450 |
|---|---|---|
| Residential and industrial estate roads | Clear road width, kerbs, leaf load and pedestrian hours | Check the footprint of J-XS1450 with the brushes deployed and plan the rounds for the debris load. |
| Factory and warehouse yards | Waste type, traffic, surface and distance to disposal | Separate sticky, entangling and special materials. Test collection and dust control on a representative stretch. |
| Car parks and connecting lanes | Gate height, narrowest section, columns and gradients | Check overall height, turning space and room to pass safely. Sweeping width alone cannot determine access. |
| Campus and public roads | Pedestrian traffic, obstructions, level changes and disposal arrangements | Choose a suitable time and arrange parking, disposal and maintenance before setting the route. |
Confirm selection against site measurements, the specified configuration and a representative trial.
Technical specifications
Review day-to-day configuration first. Expand the full specifications for more detail.
Key parameters, view at a glance
Effective sweeping width1450mm
Sweeping width1450mm
Hopper160L
Operating voltage48V
Theoretical sweeping coverage (calculated)17400㎡/h
Theoretical calculation speed12 km/h
Full specifications for ViewExpand or collapse
| Key operating figures | |||
|---|---|---|---|
| Effective sweeping width | 1450mm | Theoretical calculation speed | 12 km/h |
| Theoretical sweeping coverage (calculated) | 17400㎡/h | Sweeping width | 1450mm |
| Hopper | 160L | ||
| Drive and electrical system | |||
| Operating voltage | 48V | ||
How do these figures apply to your site?
Calculated as effective sweeping width × the website's standard theoretical speed of 12 km/h. Maximum travel speed remains a separate specification and is not used in this formula. The result is not actual or measured productivity.
Assess sweeping coverage, collection, shifts and road access before choosing for the site.
Review task-specific features, then expand the full specification and compare it against site conditions.
Structure and functions
How the systems on J-XS1450 work together
Use the exterior view for operating and maintenance orientation. Consult component documentation for internal locations.
Look at the picture to understand the equipment.
Components and their functions
01 Machine and operator station
Check the machine footprint and turning space around the factory perimeter.
02 Main brush
The main brush sweeps the floor. After shutdown, inspect it for wear and entanglement.
03 Side-brush collection
The side brush guides loose debris towards the sweeping path. Keep clearance from edges.
04 Debris collection
Empty according to waste volume, weight and disposal arrangements.
05 Filtration and dust suppression
Check media, seals and water use against the supplied configuration.
06 Drive and steering
The operator steers and yields to traffic. Maintain the power system according to the handover instructions.
Operating principle
How does J-XS1450 gather, sweep and collect debris?
This diagram explains the functions. Refer to the supplied instructions for installed parts, switching sequences and maintenance procedures.
Side-brush collection
The side brush guides suitable loose debris into the main brush path. Maintain safe kerb clearance.
Main-brush sweeping
The main brush sweeps and transfers debris. Brush condition, the surface and the material affect pickup.
Centralised collection
Plan disposal around the actual hopper load and distance to the emptying point.
Dust management and end-of-shift checks
Assess dust collection, filter cleaning and water use on site. Shut down for end-of-shift maintenance.
Filtration and dust management
How do you assess dust control on J-XS1450?
Assess filtration, collection, seals and maintenance together. A filter-area or motor rating alone cannot predict dust at the site.
Identify the material
Identify wet, sticky, hazardous, combustible or toxic material before sweeping. Special dusts require a separate method and suitable equipment.
Filtration and collection components
Identify the filter media, seals and cleaning method. Use spray only where the configuration and surface permit, and maintain the filter as specified.
Observe a representative section of road
During a trial, record dust, residue, pickup and maintenance frequency. Stop safely if anything appears abnormal. Confirm washability before rinsing the filter.
Suitable / unsuitable for boundary
Which roads suit J-XS1450, and when should another system be considered?
Candidate applications
- Estate main roads, factory surroundings and warehouse/logistics perimeters.
- Routine sweeping of longer fixed routes.
- Leaves, paper, dust and ordinary light debris.
Requires further assessment
- Large amounts of heavy debris or construction waste.
- Very narrow roads or restricted turns.
- Significant gradients.
- Prolonged continuous heavy-load operation.
- Special water-spray suppression requirements.
Comparing related models
How does J-XS1450 compare with similar models?
To compare machines, consider road layout, debris load and turning room alongside sweeping width.
| Comparison criteria | Narrower-coverage option J-XS1300 → | Current modelJ-XS1450 → | Wider-coverage option J-XS1460 → |
|---|---|---|---|
| Sweeping width | 1300mm | 1450mm | 1460mm |
| Hopper | 80L | 160L | 150L |
| Water tank | 30L | Ask about this option when specifying the machine. | 60L |
| Selection checks | Check clear road width, debris, turning room and supply points. | Check clear road width, debris, turning room and supply points. | Check clear road width, debris, turning room and supply points. |
Operating cost
What does it cost to operate J-XS1450?
Record sweeping, collection and disposal over the same period and to the same standard. Measure actual output on site.
Manual sweeping
Labour cost = crew size × hours per person × hourly rate. Record preparation, cleaning, transfers and close-down separately.
Machine option
Include operation or supervision, energy, consumables, disposal and maintenance. Allocate equipment and battery costs over a suitable service period.
On-site comparison
Record daily operating hours, routes, garbage or contaminants, and supply and shutdown times; under the same conditions, compare, and do not commit to any savings ratio that has not been calculated.
Routine maintenance
Six checks before and after using J-XS1450
Working components
Shut down safely before checking brushes for wear and entanglement. Keep hands clear of moving parts.
Hopper and disposal
Empty before reaching volume or weight limits. Hopper capacity alone does not specify safe payload.
Dust collection components
Check installed parts for dust loading, damaged media and leaks. Wash only media approved for washing.
Power and charging
Check the supplied batteries, charger and charging conditions. Have a qualified technician investigate overheating, damage or electrical faults.
Working conditions
Record changes in level, obstacles, traffic and difficult sections. Reassess the route when conditions change.
Driving and parking
Check drive, braking and parking as instructed. Stop if you hear abnormal noise or feel unexpected resistance.
Replace according to the manual, observed wear and duty. Supply the model, version and original part details when ordering.
— FAQ
Jinjie J-XS1450 ride-on sweeper: selection and operating questions
Should J-XS1450 be considered for parking or factories?
Assess both, with different priorities: bays, columns and traffic for parking, plus loading activity, grit and dust for factories. Trial the actual route rather than relying only on total area.
How should 1450 mm coverage fit narrow connections?
Measure bottlenecks and gates against the body, brushes and turning space. Use continuous passes in open areas and allow safe clearance at connections; coverage is not access width.
How should the 160 L hopper be managed?
Plan disposal around litter volume, grit weight and unloading distance. Record loading and disposal travel to divide routes into practical segments while respecting permitted loads.
How should central and edge debris be handled?
Coordinate main and side brushes with routing, remove long or large debris first and maintain edge clearance. Observe centres, kerbs and columns separately to plan manual finishing.
What matters when ordinary dust is heavy?
Assess dust properties, filters and sealing, then brushes and filter cleaning. Maintain filtration for consistent collection and assess hazardous dust separately.
How should charging and after-shift care be organised?
Provide safe charging for the actual 48 V battery and charger. Empty waste, inspect brushes, service filters and record faults after shifts, allowing maintenance time before the next team starts.
How does it compare with J-XS1300 and J-XS1460?
Listed coverage is 1450, 1300 and 1460 mm and hoppers are 160, 80 and 150 L. Compare access, filtration, power and disposal as well as similar coverage.
How can selection discussions reduce purchasing mismatch?
Share route maps, traffic, waste samples and shifts to identify configuration and trial priorities. Confirm brushes, filters, power and care at handover so procurement and operators share the same requirements.
Delivery and after-sales service
Operating and maintaining the machine after delivery
The agreed service terms specify scope, charges and timing.
01 Delivery inspection
Before handover, check the equipment, accessories and configuration against the conditions on site.
View service support →02 Operator training
Training covers driving or task operation, cleaning and safe shutdown for the equipment supplied.
View service support →03 Operator guidance
Describe the surface, debris and schedule when discussing an operating issue.
View service support →04 Parts supply
Identify spares by the machine model, version and original part.
View service support →05 On-site repairs
Confirm service area, charges and attendance arrangements in advance.
View service support →06 Scheduled on-site maintenance
Agree on maintenance arrangements based on usage, location and condition.
View service support →Tell us about the roads, debris and daily rounds so we can check the suitability of J-XS1450.
Phone consultation: 0755-25621811
Product enquiry
Tell us about the route and debris
Provide road width, sweeping area, main debris types and daily hours to assess J-XS1450.
Provide these site details to check whether J-XS1450 is suitable.
- Sweeping area / daily area
- Narrowest aisle width
- Main debris types
- Indoor / outdoor
- Is there a slope?
- Daily working time
- Water-spray dust suppression required?