01 Intended use
- Large area continuous operations, balancing refilling and maintenance
- First verify the continuous cleaning area and obstacle distribution, then compare the smaller models with combined operation methods.
Jinjie Floor Scrubber
Jinjie J-105BF Large Ride-On Floor Scrubber
Jinjie J-105BF large driver-type floor scrubber, designed for wider working areas on factory hard surfaces, operates with 1050 mm brushing and 180 L/190 L dual water tanks. Particle pre-cleaning, wastewater recovery, and refilling must be connected in a continuous process.
Established in 2004 | Site-trial discussion | Service support across China
Theoretical calculation speed:10 km/hTheoretical cleaning coverage (calculated)10500㎡/hWebsite theoretical comparison calculation; not actual productivity.
02 Key performance figures
- Cleaner width and water tank configuration.
- 1050 mm clear width; water tank capacity 180 L / 190 L. Actual performance should be confirmed in combination with the floor material, dirt type, and on-site trial operation.
03 Working configuration
- Operation and daily usage scheduling
- Operated by personnel. When selecting, confirm battery, charging location, and daily inspection and maintenance arrangements together.
Start with your site
Choose the area that best matches your site
First, distinguish the main working area, logistics crosspoints, areas where the machine is difficult to reach, and potential areas where particles may get entangled. The wide coverage of J-105BF should be checked together with the outer edge of the 1300 mm squeegee and the turning space; record the time for pre-cleaning, brushing, recovery, and finishing, then determine whether the entire task matches the team.
How can large area ride-on floor scrubbers be coordinated with your site?
First, check the on-site conditions, then determine the appropriate equipment configuration together.
Commercial spaces and shopping malls.
Channel width, turning position, business hours.
Office and public buildings
Handling large crowds, corridors, and elevators
Property management garage and public areas
Conditions of hard surfaces, drainage, and ramps
Factory and warehouse floor cleaning equipment.
Oil stains, dust, obstacles, and work routes
| Site type | The on-site conditions for joint checking | J-105BF Selection Recommendation |
|---|---|---|
| Commercial spaces and shopping malls. | Channel width, turning position, business hours. | First confirm whether the equipment can turn and pass, then divide the continuous cleaning area. |
| Office and public buildings | Handling large crowds, corridors, and elevators | Verify the passage and floor transfer conditions; in narrow areas, pair with smaller models. |
| Property management garage and public areas | Conditions of hard surfaces, drainage, and ramps | Clarify and level the work area; slopes and elevation differences must be checked against the technical specifications of this machine. |
| Factory and warehouse floor cleaning equipment. | Oil stains, dust, obstacles, and work routes | First distinguish the type of dirt and the floor surface material, then arrange pre-treatment, brushing, and wastewater recovery. |
Daily cleaning, try a more convenient method.
How can we reduce the effort of pushing the machine over a large floor?
Starting from the areas you clean daily, consider how driving operations, brushing, and wastewater recovery can be integrated into your daily routine. Please let us know your route and usage schedule, and we will assess together.
01
How to schedule cleaning in coordination with production?
Schedule cleaning zone by zone around production. Check the soil, clearances between machines and travel routes before planning scrubbing and wastewater recovery.
Look at relevant scenarios →
02
How to schedule cleaning in coordination with production?
Schedule cleaning zone by zone around production. Check the soil, clearances between machines and travel routes before planning scrubbing and wastewater recovery.
Look at relevant scenarios →
03
How to schedule cleaning in coordination with production?
Schedule cleaning zone by zone around production. Check the soil, clearances between machines and travel routes before planning scrubbing and wastewater recovery.
Look at relevant scenarios →TECHNICAL SPECIFICATIONS
Ride-On Floor ScrubbersJ-105BF configuration and technical parameters
First understand several configurations closely related to daily use. Detailed specifications are also organized below for easy comparison.
First check these core configurations.
Cleaning width1050mm
Fresh water tank / Sewage water tank180L / 190L
Runtime reference4–6h
Battery6 × 6V × 200Ah
Theoretical cleaning coverage (calculated)10500㎡/h
Operating voltage36V
Full specifications for ViewCleaning performance · Power and charging · Overall configurationExpand or collapse
Detailed equipment specifications
| Key operating figures | |||
|---|---|---|---|
| Cleaning width | 1050mm | Squeegee width | 1300mm |
| Clean water tank | 180L | sewage tank | 190L |
| Runtime reference | 4–6h | Theoretical cleaning coverage (calculated) | 10500㎡/h |
| Forward speed | 0–10km/h | Reverse speed | 3km/h |
| Theoretical calculation speed | 10 km/h | Maximum travel speed | 10 km/h |
| Drive and electrical system | |||
| Operating voltage | 36V | Battery | 6 × 6V × 200Ah |
| Travel motor | 1200W | Brush motor | 600W × 2 |
| Machine configuration | |||
| Product model | J-105BF | Work method | Ride-on |
How do these figures apply to your site?
Note: website theoretical coverage for ride-on scrubber-dryers is calculated as cleaning width × the standard theoretical calculation speed of 10 km/h. It is for theoretical area comparisons, not actual productivity or the machine's maximum travel speed.
Look beyond the numbers: consider how they affect coverage of large open zones, filling/draining frequency, continuous routes and access limits.
10500 m²/h is calculated from the confirmed cleaning width × the website theoretical calculation speed of 10 km/h. It is for theoretical coverage comparisons only, not actual or measured productivity.
Drive-type operation.Brushing and cleaning.Extract wastewater
Look at the picture to understand the equipment.
Components and their functions
01 Driving and Drive
Sitting driving to reduce the continuous pushing over longer routes, and operating in coordination with on-site traffic.
02 brushing configuration
1050 mm cleaning width, brush disk motor 600 W × 2; determine the cleaning configuration based on the floor material and dirt.
03 Wastewater recovery
The width of the squeegee is 1300 mm. The washing and wastewater recovery system combines, and actual residual water can be confirmed through on-site testing.
04 Dual water tank configuration
180 L clear water tank, 190 L wastewater tank, combine zone division and water and drainage position arrangement for operations
05 Battery and Shifts
36 V working voltage, battery is 6 × 6 V × 200 Ah; schedule shifts according to actual working conditions.
06 Route and traffic
Check together the entrance, passage, turning space, ramp, and slippery areas for additional confirmation.
Understanding the specifications
How do these configurations correspond to your daily work?
Digital solutions must ultimately be put to use: how the route is arranged, whether water and drainage are convenient, and how shifts are scheduled. We combine key configurations with on-site conditions to help you make judgments.
1050 mm clear width, combined with actual route arrangement for continuous operation.
Check together: narrowest entrance / passage / turning space.180 L clear water tank and 190 L wastewater tank, coordinate with zone division cleaning arrangement
Take a look: water refill points / drainage points / cleaning area per session.Combine the machine's drive configuration and on-site route to reduce continuous pushing.
Take a look: continuous route / operating habits / ramp conditions.Arrange shifts based on the machine's battery and actual usage conditions.
Take a look: daily operating time / usage frequency / charging location.Judge together whether it is appropriate
Is J-105BF suitable for you? Let's compare together
In these cases, you can first refer to J-105BF.
- Large continuous hard-floor areas
- Underground car parks, logistics parks, airports, stations and large shared areas
- Open routes with ride-on access
- Need fewer filling/draining stops and repeated manual trips
These requirements also warrant comparison with other models.
- Not recommended for confined spaces or frequent tight turns
- For smaller areas, compare J-D9BF/J-85BH or a smaller model
- Pre-clear substantial loose debris first
- If there are steps or slippery areas, confirm the passage conditions together.
Compare related models
How to choose the right model for J-105BF compared to similar models?
Place the three models together and see the differences in configuration and operating method.
| Comparison criteria |  J-960B → | J-105BF → |  J-SX1360D → |
|---|---|---|---|
| Cleaning width | 960mm | 1050mm | Request the specification for this configuration. |
| Squeegee width | 1100mm | 1300mm | 1200mm |
| Clean water tank | 180L | 180L | 200L |
| sewage tank | 200L | 190L | 260L |
| Battery configuration | 36V × 200Ah | 6 × 6V × 200Ah | 48V150Ah |
| Work time for the data. | Request the specification for this configuration. | 4–6h | Request the specification for this configuration. |
| Operating method | Operator-controlled. | Operator-controlled. | Operator-controlled. |
First, check the passage and operation mode, then compare the water tank, working time, and maintenance schedule. The data in the table is based on the current technical specifications of each model. The working time of the machine is not equal to the actual runtime under all operating conditions. A wash and sweep combined machine belongs to a different operating mode, and both sweeping and scrubbing tasks need to be checked simultaneously. Upgrading is not just determined by the width.
Related articles
Are there any questions about selection? You can continue to look at these contents.
Combine the machine's configuration to continue understanding these issues.
- Why should workshop metal shavings be suctioned first before floor scrubbing: a combination of industrial vacuum and floor scrubber is more stable →Removing loose debris before scrubbing factory floors
Operating cost
How can the usage cost of J-105BF be calculated more accurately in the field?
Compare using the same floor, same cleaning requirements, and actual records.
First, record the actual investment.
Labor cost = number of people × actual working hours × hourly labor cost.
Record actual expenditure on tools, detergent and clean-up.
Include operation and maintenance together
Single-use cost = operator labor + water and electricity with cleaning agent + consumable maintenance allocation + equipment investment allocation.
Turns, water replenishment, sewage discharge, and cleaning conclusion should all be counted as actual working time.
From the site, let's select the appropriate one together.
Understand similar operating conditions, then confirm the suitability of this machine.
First, check the application scenario of this page. Combine it with your floor type, route, and work schedule to make a judgment. Real customer projects are only displayed according to the verified model, and the scenario images are not used as proof of customer results.
Understand customer applications → Talk about the site and trial run →On-site applications
J-105BF Application Real Shots
Workshop-aisle floor cleaning
Workshop-aisle floor cleaning
A workshop-aisle application shows ride-on floor washing and wastewater recovery.
- Continuous cleaning along workshop aisles
- Combined scrubbing and wastewater recovery
Service support
Operating and maintaining the machine after delivery
Delivery inspection
Check the equipment and configuration list together before delivery.
Understand service arrangements →Operator training
Communicate startup, brushing, replenishment of water, and daily cleaning.
Understand service arrangements →Usage guidance
In case of operational issues, communicate with the model and usage conditions.
Understand service arrangements →Parts supply
Check the brush roll, rubber strip, and other parts against the model.
Understand service arrangements →On-site fault repair
Service scope, costs, and arrival arrangements need to be confirmed first.
Understand service arrangements →Scheduled on-site maintenance
Coordinate maintenance plans with the frequency of use and the location.
Understand service arrangements →— FAQ
Choosing and using the J-105BF: frequently asked questions
Which large factory routes suit the J-105BF scrubber?
Consider open continuous hard-floor areas after assessing soil and logistics traffic. Metal chips, cords and packaging are not automatically suitable for direct scrubbing; arrange appropriate pre-cleaning and waste handling.
What should be checked before J-105BF cleans concrete, dry-shake or epoxy factory floors?
For J-105BF factory routes, inspect concrete hardening, dusting and damage and dry-shake texture and sealing, collecting loose grit and debris first. On epoxy, confirm coating condition and curing and use compatible brushes or pads and low-foam chemistry. Trial a representative area for even scrubbing, blade contact, water residue and finishing at turns before planning wide routes. Cleaning width and tank size do not establish suitability for every oily soil or damaged floor.
How should access be checked for J-105BF's 1050 mm width and 1300 mm squeegee?
These are separate coverage and recovery dimensions. Check the complete envelope, turns and operating clearance, including connecting doors, pillars, parking and service space. Cleaning width alone does not establish passage.
How should filling and draining be planned for J-105BF's 180 L and 190 L tanks?
In conjunction with the waste material, water supply setup, and repeated scrubbing requirements, first confirm the refilling and drainage points, then record the actual refilling times along the representative route. 180 L clean water tank and 190 L dirty water tank are used for planning refilling, which do not directly equate to a fixed cleaning area; the time for going and returning for scrubbing should be recorded separately.
How should long routes and charging shifts be planned for J-105BF?
Check the corresponding battery and load and record site use. Factory shifts also need charging, replenishment and maintenance time. Powered-on, travelling and effective scrubbing time are different measures.
How should a large factory scrubber work alongside edge-cleaning tools?
Use J-105BF on suitable wide main routes and assign appropriate tools or processes to edges, steps, under-equipment areas and special soil. Plan pre-sweeping, main-route scrubbing, finishing and waste handling together to avoid missed areas.
How should one-sided scrubbing or recovery faults on J-105BF be checked?
First, safely shut down the machine according to the instructions, and separately check for worn brushes and foreign objects, the rubber strip's contact with the ground, and the sealing hose circuit for recovery. Do not disassemble the motor while it is still energized. Record the abnormal location, dirt, and operating conditions to assist the after-sales service team in further judgment.
What site requirements should be shared with Wanshenglong when selecting J-105BF?
Provide open working areas, logistics routes, soil, door dimensions and water points, including pre-cleaning and finishing arrangements. Wanshenglong can discuss configuration, trials and training without presenting a generic case as this machine’s acceptance evidence.
Discuss the floor, routes, and daily cleaning schedule, and together see if J-105BF is suitable.
Phone consultation: 0755-25621811 View other contact information →
Product enquiryDiscuss your site, and together see if J-105BF is suitable
Tell us about the usage area and the issues you hope to improve, and the equipment consultant will combine with the passage, ground and work arrangement, communicate the suitable configuration with you. The area is temporarily unclear, you can contact us first.