01 Intended use
- Driving operation, balancing passage and route.
- First confirm whether the equipment can enter and complete the turn, then compare the areas that need to be cleaned each day.
Jinjie Floor Scrubber
Jinjie J-D6SL 560 mm Ride-On Floor Scrubber
The Jinjie J-D6SL serves fixed cleaning routes in shopping and property common areas, combining 560 mm scrubbing with 70 L/75 L tanks and seated operation. Assess access, pedestrians and water handling first.
Established in 2004 | Site-trial discussion | Service support across China
Theoretical calculation speed:10 km/hTheoretical cleaning coverage (calculated)5600㎡/hWebsite theoretical comparison calculation; not actual productivity.
02 Key performance figures
- Cleaner width and water tank configuration.
- 560 mm clear width; water tank capacity 70 L / 75 L. Actual performance should be confirmed in combination with the floor material, dirt type, and on-site trial operation.
03 Working configuration
- Operation and daily usage scheduling
- Operated by personnel. When selecting, confirm battery, charging location, and daily inspection and maintenance arrangements together.
Start with your site
Choose the area that best matches your site
When replacing walk-behind work, check operator control, route direction and crossing areas. Measure doors, lifts, corners and storage against the actual envelope, not the 560 mm cleaning width. Include water handling, charging and finishing time instead of relying on theoretical area.
How can the compact driving floor scrubber be matched with your site?
First, check the on-site conditions, then determine the appropriate equipment configuration together.
Commercial spaces and shopping malls.
Channel width, turning position, business hours.
Office and public buildings
Handling large crowds, corridors, and elevators
Property management garage and public areas
Conditions of hard surfaces, drainage, and ramps
Factory and warehouse floor cleaning equipment.
Oil stains, dust, obstacles, and work routes
| Site type | The on-site conditions for joint checking | J-D6SL Selection Recommendation |
|---|---|---|
| Commercial spaces and shopping malls. | Channel width, turning position, business hours. | First confirm whether the equipment can turn and pass, then divide the continuous cleaning area. |
| Office and public buildings | Handling large crowds, corridors, and elevators | Verify the passage and floor transfer conditions; in narrow areas, pair with smaller models. |
| Property management garage and public areas | Conditions of hard surfaces, drainage, and ramps | Clarify and level the work area; slopes and elevation differences must be checked against the technical specifications of this machine. |
| Factory and warehouse floor cleaning equipment. | Oil stains, dust, obstacles, and work routes | First distinguish the type of dirt and the floor surface material, then arrange pre-treatment, brushing, and wastewater recovery. |
Daily cleaning, try a more convenient method.
How can we reduce the effort of pushing the machine over a large floor?
Starting from the areas you clean daily, consider how driving operations, brushing, and wastewater recovery can be integrated into your daily routine. Please let us know your route and usage schedule, and we will assess together.
01
How can we clean a large area while people are moving through it?
Coordinate cleaning schedules with foot traffic, combining brushing and wastewater recovery to reduce repeated scrubbing and accommodate personnel movement.
Look at relevant scenarios →
02
The route is long, and manual pushing is labor-intensive.
Operator-driven operation reduces the need for prolonged pushing along long routes, with the machine cleaning and recovering wastewater in designated parking areas and main channels, and the slope conditions are also checked together.
Look at relevant scenarios →
03
How to arrange routes when there are a lot of goods and vehicles
Perform operations in sections according to the rack and passage division, and confirm the turning space, vehicle passage, and drainage and replenishment positions together, making the cleaning more systematic.
Look at relevant scenarios →TECHNICAL SPECIFICATIONS
Ride-On Floor ScrubbersJ-D6SL configuration and technical parameters
First understand several configurations closely related to daily use. Detailed specifications are also organized below for easy comparison.
First check these core configurations.
Cleaning width560mm
Fresh water tank / Sewage water tank70L / 75L
Runtime reference3–4h
Battery24V / 100Ah
Theoretical cleaning coverage (calculated)5600㎡/h
Machine dimensions1460 × 830 × 1100mm
Full specifications for ViewCleaning performance · Power and charging · Overall configurationExpand or collapse
Detailed equipment specifications
| Key operating figures | |||
|---|---|---|---|
| Cleaning width | 560mm | Squeegee width | 780mm |
| Clean water tank | 70L | sewage tank | 75L |
| Runtime reference | 3–4h | Theoretical cleaning coverage (calculated) | 5600㎡/h |
| Theoretical calculation speed | 10 km/h | ||
| Drive and electrical system | |||
| Operating voltage | 24V | Battery | 24V / 100Ah |
| Travel motor | 24V / 500W | Brush motor | 24V / 500W |
| Recovery motor | 24V / 500W | ||
| Machine configuration | |||
| Machine dimensions | 1460 × 830 × 1100mm | Machine weight | 155kg |
| Product model | J-D6SL | Work method | Ride-on |
| Brush size | 560mm | ||
How do these figures apply to your site?
Note: website theoretical coverage for ride-on scrubber-dryers is calculated as cleaning width × the standard theoretical calculation speed of 10 km/h. It is for theoretical area comparisons, not actual productivity or the machine's maximum travel speed.
The cleaning width affects the coverage of a single pass, and the relationship between the fresh water tank and the dirty water tank affects the convenience of continuous operation. The battery, drive, and water suction system affect the daily floor scrubbing schedule.
5600 m²/h is calculated from the confirmed cleaning width × the website theoretical calculation speed of 10 km/h. It is for theoretical coverage comparisons only, not actual or measured productivity.
Drive-type operation.Brushing and cleaning.Extract wastewater
Look at the picture to understand the equipment.
Components and their functions
01 Driving and Drive
Sitting driving to reduce the continuous pushing over longer routes, and operating in coordination with on-site traffic.
02 brushing configuration
560 mm cleaning width, brush disk motor 24 V / 500 W; combine with floor material and dirt to confirm cleaning configuration.
03 Wastewater recovery
The width of the squeegee is 780 mm. The washing and wastewater recovery system combines, and actual residual water can be confirmed through on-site testing.
04 Dual water tank configuration
70 L clear water tank, 75 L wastewater tank, combine zone division and water and drainage position arrangement for operations
05 Battery and Shifts
24 V working voltage, battery is 24 V / 100 Ah; schedule shifts according to actual working conditions.
06 Route and traffic
Check together the entrance, passage, turning space, ramp, and slippery areas for additional confirmation.
Understanding the specifications
How do these configurations correspond to your daily work?
Digital solutions must ultimately be put to use: how the route is arranged, whether water and drainage are convenient, and how shifts are scheduled. We combine key configurations with on-site conditions to help you make judgments.
560 mm clear width, combined with actual route arrangement for continuous operation.
Check together: narrowest entrance / passage / turning space.70 L clear water tank and 75 L wastewater tank, coordinate with zone division cleaning arrangement
Take a look: water refill points / drainage points / cleaning area per session.Combine the machine's drive configuration and on-site route to reduce continuous pushing.
Take a look: continuous route / operating habits / ramp conditions.Arrange shifts based on the machine's battery and actual usage conditions.
Take a look: daily operating time / usage frequency / charging location.Judge together whether it is appropriate
Is J-D6SL suitable for you? Let's compare together
In these cases, you can first refer to J-D6SL.
- Continuous hard-floor areas
- Underground-car-park, shopping-centre, property or factory passages
- The route permits ride-on access
- Need to reduce walking effort
These requirements also warrant comparison with other models.
- Not recommended for confined spaces or frequent tight turns
- For smaller areas, compare J-D5SL or J-D3L
- Pre-clear substantial loose debris first
- If there are steps or slippery areas, confirm the passage conditions together.
Compare related models
How to choose the right model for J-D6SL compared to similar models?
Place the three models together and see the differences in configuration and operating method.
| Comparison criteria |  J-56BF → | J-D6SL → |  J-D7SL → |
|---|---|---|---|
| Cleaning width | 560mm | 560mm | 710mm |
| Squeegee width | 800mm | 780mm | Request the specification for this configuration. |
| Clean water tank | 70L | 70L | 70L |
| sewage tank | 75L | 75L | 75L |
| Battery configuration | 2 × 12V / 100Ah | 24V / 100Ah | 24V/100Ah |
| Work time for the data. | 3–4h (reference value) | 3–4h | 3–4h |
| Operating method | Operator-controlled. | Operator-controlled. | Operator-controlled. |
First, check the passage and operation methods, then compare the water tank, working time, and maintenance schedule. The data in the table is based on the current technical specifications of each model. The working time in the documentation does not equal the actual runtime under all operating conditions.
Related articles
Are there any questions about selection? You can continue to look at these contents.
Combine the machine's configuration to continue understanding these issues.
- How to distinguish the model of the floor scrubber: J-D3L, J-D5SL, J-D6SL are suitable for what site →Understanding the actual differences between hand-pushed, self-propelled, and ride-on types
Operating cost
How can the usage cost of J-D6SL be calculated more accurately in the field?
Compare using the same floor, same cleaning requirements, and actual records.
First, record the actual investment.
Labor cost = number of people × actual working hours × hourly labor cost.
Record actual expenditure on tools, detergent and clean-up.
Include operation and maintenance together
Single-use cost = operator labor + water and electricity with cleaning agent + consumable maintenance allocation + equipment investment allocation.
Turns, water replenishment, sewage discharge, and cleaning conclusion should all be counted as actual working time.
From the site, let's select the appropriate one together.
Understand similar operating conditions, then confirm the suitability of this machine.
First, check the application scenario of this page. Combine it with your floor type, route, and work schedule to make a judgment. Real customer projects are only displayed according to the verified model, and the scenario images are not used as proof of customer results.
Understand customer applications → Talk about the site and trial run →Service support
Operating and maintaining the machine after delivery
Delivery inspection
Check the equipment and configuration list together before delivery.
Understand service arrangements →Operator training
Communicate startup, brushing, replenishment of water, and daily cleaning.
Understand service arrangements →Usage guidance
In case of operational issues, communicate with the model and usage conditions.
Understand service arrangements →Parts supply
Check the brush roll, rubber strip, and other parts against the model.
Understand service arrangements →On-site fault repair
Service scope, costs, and arrival arrangements need to be confirmed first.
Understand service arrangements →Scheduled on-site maintenance
Coordinate maintenance plans with the frequency of use and the location.
Understand service arrangements →— FAQ
Jinjie J-D6SL 560 mm ride-On floor scrubber selection and common issues
Which commercial cleaning routes suit the J-D6SL ride-on scrubber?
It can be considered as a candidate for fixed route scrubbing in commercial areas and public spaces. First, check the floor type, pedestrian flow, and turning conditions, then determine whether the operation is convenient. Areas such as small corners, steps, and locations that cannot be reached by the machine should be handled with other cleaning methods.
What should be checked on epoxy, concrete and dry-shake garage floors with J-D6SL?
Before using J-D6SL in a garage, distinguish epoxy coatings, hardened concrete and dry-shake floors. Check epoxy condition and curing and select compatible soft brushes or pads. Inspect concrete for loose material, dusting and absorption and collect grit first. On dry-shake floors, also assess texture and sealing, trial brushes and check blade contact. Test all surfaces for damage, residual soil and water. Assess ramps separately against the machine’s permitted conditions.
How should J-D6SL's 560 mm width and 70 L/75 L tanks be matched to a site?
Coverage affects each pass; tanks affect replenishment. Record turning, yielding and water handling on a real route. Capacity alone cannot promise a fixed cleaned area.
How should charging and daily cleaning shifts be planned for J-D6SL?
Use it as configuration information subject to battery condition and load. Allow for collection, replenishment, cleanup and charging; shift duration is not the same as uninterrupted effective scrubbing.
How should J-D6SL and J-D7SL ride-on scrubbers be compared?
The two models should be compared under the same task. J-D6SL is in the 560 mm direction, J-D7SL is in the 710 mm dual brush direction; in addition to coverage, attention should also be paid to the outer edge of the squeegee, route overlap, turns, and refilling, and the throughput capacity should not be inferred solely based on the model number.
How should garage ramps and wet-route conditions be checked for a ride-on scrubber?
Check the equipment’s permitted conditions, measure the ramp and assess wet surfaces, turns, braking and crossing traffic. Assess flat-floor and ramp work separately. Drive type or motor power alone does not establish suitability; exclude unconfirmed sections from the route.
How should scrubbing and recovery be checked when a ride-on leaves residual water?
Shut down safely according to the instructions, check the wastewater tank and seal, the suction hose and rubber seal. Sharp turns, seams, or foreign objects may also affect the recovery; if unable to resolve, provide on-site photos without powering the machine.
What requirements should be shared with Wanshenglong when selecting J-D6SL?
Provide fixed routes, peak pedestrian times, floor materials, doorways, elevators, and replenishment and drainage points, and explain the team's driving experience. Wanshenglong will focus on the configuration, trial use, training, and part communication of Jinjie equipment. The specific service scope will be confirmed according to the project.
Discuss the floor, routes, and daily cleaning schedule, and together see if J-D6SL is suitable.
Phone consultation: 0755-25621811 View other contact information →
Product enquiryDiscuss your site, and together see if J-D6SL is suitable
Tell us about the usage area and the issues you hope to improve, and the equipment consultant will combine with the passage, ground and work arrangement, communicate the suitable configuration with you. The area is temporarily unclear, you can contact us first.