APPLICATION GUIDANCE · RIDE-ON SCRUBBER SELECTION
Jinjie J-D9R Ride-on Floor Scrubber · Typical application
Factory main-aisle cleaning
Plan scrubbing and recovery along continuous indoor main aisles and equipment perimeters. Distinguish light soil, production debris and heavy grease before selecting brushes and the working method.
- 860mm · cleaning width
- 140L / 150L · solution / recovery
- 24V / 200Ah
01 · Understand the cleaning task
Coordinate people, material transport and equipment boundaries. Dust, footprints and local deposits do not all call for the same treatment.
Production and cleaning
Coordinate cleaning with material movements and maintenance while keeping safety access open.
Mixed soil
Remove metal chips, straps and large particles first; assess heavy grease separately.
Continuous routes and drainage
Divide work by flooring, routes and water points; discharge wastewater only at approved locations.
02 · Why consider this model
J-D9R specifies 860mm twin-disc cleaning, a 140L solution tank and 150L recovery tank. Consider it for this ride-on task after checking access, flooring and working conditions.
Driving and route planning
An operator drives, scrubs and recovers water. Plan stops, turns and operating periods; no automatic obstacle avoidance is claimed.
860mm cleaning configuration
Cleaning width describes coverage, not access clearance. Trial brushes on the actual floor.
140L / 150L separate tanks
Plan filling and draining by soil, water use and drainage routes; no fixed runtime is promised.
03 · Prepare, clean and inspect
Prepare the site
Agree production boundaries and remove metal chips, entangling objects and loose particles.
Plan route and equipment
Trial suitable brushes and water use on the floor and plan main-aisle and perimeter routes.
Clean in zones
Scrub and recover in sections without contacting running equipment or obstructing safety access.
Inspect recovery
Inspect joints and equipment edges for water, handle wastewater correctly and clean and inspect the machine.
SITE → CONFIGURATION → DECISION
04 · Check the conditions before selection
| Site condition | Configuration or arrangement | Decision check |
|---|---|---|
| Equipment perimeters, material aisles and turns | 860mm cleaning / 1200mm recovery | Measure the full envelope, turns and passing space rather than brush width alone. |
| Factory flooring and production soil | Matched brush, water and recovery | Trial a small area; confirm heavy grease, coatings and special surfaces separately. |
| Shifts, filling points and approved drainage | 140L solution / 150L recovery | Plan from actual soil, water use and site services; capacity does not guarantee working time. |
| Workload | 5500m²/h supplied efficiency figure | Test conditions were not supplied. Actual output includes transfers, turns, water servicing and care. |
05 · Operating limits and safety
- Follow the operating manual, zone the work area and keep people, vehicles and site equipment clear.
- Remove large particles and entangling items first; the scrubber is not described as a debris-collection machine.
- Confirm slope, loading, floor tolerance and charging against the supplied manuals; an image does not establish access capability.
- Assess standing water, corrosive or flammable materials and damaged floors separately from routine light-soil tasks.
06 · Care for the machine after this task
Brushes and blades
After shutdown and power isolation, check wear and entanglement, remove blade deposits and inspect squeegee contact.
Tanks and recovery hoses
Drain and clean the recovery tank according to the manual; check hose blockage, seals and residual water.
Battery and handover
Charge according to the matched battery and charger manuals, record abnormalities and never dismantle during operation.
07 · Questions about this application
Can J-D9R be used in every factory hard floors setting?
No. Check equipment perimeters, material aisles and turns, factory flooring and production soil and water servicing at the actual site.
Does 860mm cleaning width define aisle clearance?
No. Check the body and 1200mm squeegee envelope, turns, obstacles and passing space.
How should the 140L/150L tanks be serviced?
Plan around shifts, filling points and approved drainage, actual soil and water use, using approved filling and drainage points.
Will this task achieve 5500m²/h?
That is the supplied work-efficiency figure without test conditions, not guaranteed output or a labour-saving promise for this application.
Can it work directly on ramps or special floors?
A level-floor reference image is not evidence. Check ramps, floor tolerance, brushes and loading against machine data and site requirements.
08 · Other applications for this model
Share your site conditions
Share the floor material, area, equipment perimeters, material aisles and turns, operating periods and filling/drainage points to assess J-D9R.
0755-25621811